Evoko Liso Factory Reset Verified |link| (2025-2027)
Locate the physical reset button on the Evoko Liso. It is a small pinhole located on the back or bottom edge of the device, near the cable connections.
Resetting an Evoko Liso room manager becomes necessary when the device experiences screen freezes, loses its network connection, or needs to be prepared for a new server configuration. Because these devices lack an external physical reset button, triggering a factory restore requires specific, validated sequences.
The necessity for a factory reset on an Evoko Liso unit typically arises from three primary scenarios. The most common is the "handover" phase, where a device is moved from one meeting room to another, or when an organization decommissions a unit. In these cases, it is vital to purge all previous configuration data, including network credentials, calendar integrations, and unique room identifiers, to prevent data leakage or cross-room scheduling errors. Secondly, a reset is often the final troubleshooting step when a device becomes unresponsive or fails to synchronize with the central server. When standard reboots fail, wiping the slate clean is often the only way to resolve deep-seated software conflicts. Finally, a verified reset is essential during the resale or disposal of hardware, ensuring that corporate network passwords and proprietary settings do not fall into unauthorized hands.
We've verified two methods for performing a factory reset on your Evoko Liso device. Please follow the steps carefully to ensure a successful reset. evoko liso factory reset verified
Evoko Liso is a meeting-room touch panel used for room booking. A factory reset restores the device to original settings, wiping local configuration (Wi‑Fi, server addresses, schedule data). Verified procedures vary by firmware; below is a concise, actionable guide plus risks and verification steps.
If recognized, the screen will display an update/installation progress bar. Do not remove power during this process.
: Download the latest Liso Device Reset (GZ file) from the official Biamp Downloads page . Use imaging software like Etcher, Rufus, or Win32 Disk Imager to flash this file onto your USB drive (this will erase all data on the USB). Locate the physical reset button on the Evoko Liso
If your Evoko Liso screen is responsive and connected to the network, the cleanest way to reset the device is through the Evoko Home management application. This removes the device safely from your server ecosystem. Step-by-Step Instructions
| Issue | Possible Cause | Solution | | :--- | :--- | :--- | | USB drive not recognized by the Liso | Using an incompatible or low-quality USB drive; image not written correctly. | Use a physically small, high-quality USB drive from a brand other than Kingston. Recreate the bootable drive using Etcher carefully. | | Windows prompts to format the USB drive after creation | Normal behavior; the drive has a Linux-based file structure that Windows cannot read. | Ignore the message and do not format the drive. Proceed to use it in the Liso. | | Liso boots normally, ignoring the USB drive | USB port is faulty; USB drive not inserted before power-on. | Ensure you insert the USB drive before powering on the Liso. Try a different USB port if available. | | Reset process seems to hang or takes over 15 minutes | Corrupted firmware file; USB drive is too slow; hardware issue. | Download a fresh copy of the firmware reset file. Recreate the USB drive. If the problem persists, contact Biamp Support. | | "Flash complete!" message not displayed | Reset was interrupted; USB drive removed too early. | Repeat the entire process from Step 2, ensuring the USB drive remains inserted until the completion message appears. | | After reset, Liso won't connect to Evoko Home | Network settings not configured; Liso still has old server information cached. | Go through the initial setup process and ensure the correct Evoko Home server IP address is entered. |
: Wait for the message: "Flash has been successfully completed!" . Because these devices lack an external physical reset
Not a simple "push-pin" reset; requires external software and a specific USB preparation. 5-10 minutes.
Insert the prepared USB drive into the port on the back of the device. the device. Complete the Flash :
Before starting the reset process, gather the necessary equipment and back up essential data. A factory reset wipes all local configurations, including IP addresses, certificates, and server connection strings.
If the Liso screen is currently , frozen , or displaying an error message .
However, if the Liso is frozen, the USB flash method (above) is the only verified solution. Troubleshooting the Reset Process
